Video surveillance has become an essential element in condominiums, offices and commercial spaces. However, installing an NVR (Network Video Recorder) system with IP cameras on a distributed Wi-Fi network goes far beyond connecting equipment and installing an app. When the network infrastructure is not properly configured, problems arise ranging from cameras being invisible to the NVR to distorted images and delays in video transmission.
In this practical guide, we explain how to plan and carry out a complete NVR system installation with IP cameras in a Wi-Fi environment, covering access point configuration, centralized IP address management, storage sizing and troubleshooting the most common issues. If you are considering implementing video surveillance in your company or condominium, this article is the right starting point.
Preparing the Storage: The NVR Disk
The first step in an NVR installation is ensuring the equipment has adequate storage capacity. Modern NVRs support 3.5-inch SATA disks, and choosing the right disk is crucial for long-term reliability.
- Use disks certified for video surveillance: Models such as WD Purple, Seagate SkyHawk or Toshiba S300 are optimized for continuous writing, unlike general-purpose disks that can fail prematurely in this context.
- Size the capacity in advance: For 4 Full HD cameras with motion recording, 1 TB guarantees about 10 to 14 days of retention. For 30 days or more, opt for 4 TB or higher.
- Format the disk through the NVR: After installing the disk, the NVR should be responsible for formatting it, as it uses its own file system optimized for continuous video streams.
- Check compatibility: Always consult the NVR manufacturer’s list of compatible disks before purchasing the storage equipment.
A poorly chosen or incorrectly installed disk can result in corrupted recordings or total loss of footage, which compromises the entire usefulness of the surveillance system.
Configuring the Network: APs, Centralized DHCP and Subnets
This is the most critical step and the one that most often causes problems in video surveillance installations. When there are several Wi-Fi access points distributed across different floors or zones, it’s tempting to leave each router running in its default mode. This is a common mistake with serious consequences for communication between cameras and the NVR.
The problem with routers in router mode: When two or more routers are active in router mode, each one creates its own isolated subnet. A camera connected to the router on floor 2 ends up on a different network from the NVR connected to the router on floor 0, making direct communication between the two impossible.
The correct solution is to configure all secondary routers in AP (Access Point) mode:
- The main router, installed in the rack or technical room, is the only one acting as a router and DHCP server.
- All other routers are configured as APs, disabling their DHCP and connecting them to the main router via Ethernet cable.
- All devices, cameras and NVR, stay on the same subnet and obtain IP addresses from the same centralized DHCP server.
- The NVR should receive a static IP address or a DHCP reservation, so that its address does not change between restarts.
A typical stable configuration for this type of installation uses the 192.168.3.x subnet, with the DHCP pool assigning addresses between 192.168.3.100 and 192.168.3.254, reserving addresses below 100 for devices with static IP such as the NVR and any managed switches.
Adding Cameras to the NVR and Checking the Monitoring App
With the network correctly configured, the NVR can automatically discover the cameras through protocols such as ONVIF or the manufacturer’s proprietary protocols. However, there are a few points to check before considering the installation complete:
- Confirm that all cameras have an IP on the correct subnet: Access the NVR’s web interface and check the IP addresses assigned to each camera. A camera with an IP on a different subnet will not be detected.
- Test the image quality of each camera individually: Distorted, pixelated or incorrectly coloured images can indicate a camera with a damaged sensor, which should be replaced.
- Set up the mobile monitoring app: Most NVRs include a mobile app (such as eWent, Hik-Connect or similar). Add the NVR to the app using its serial number or IP address and check that you can view all feeds remotely.
- Set the recording schedules: Configure continuous recording or motion-detection recording as needed, and check that recordings are actually being saved to the disk.
Resolving Wi-Fi Signal Issues: Lag and Reduced Image Quality
Even with a well-configured network, cameras installed in areas with weak Wi-Fi signal, such as building entrances, garages or outdoor areas, may experience transmission delays (lag) or loss of image quality. This is one of the most frequent problems in real-world installations.
The most effective solution is installing a Wi-Fi repeater or additional access point near the problematic camera. A few important points to consider:
- Prefer an AP with an Ethernet cable connection to the main router rather than a pure Wi-Fi repeater, as this avoids the signal degradation inherent to wireless repetitions.
- If a cable is not feasible, a quality Wi-Fi repeater installed halfway between the main AP and the camera solves most cases of lag.
- A lag of 1 to 2 seconds is acceptable in many IP video surveillance systems over Wi-Fi. Lag above 5 seconds indicates a signal problem that requires intervention.
- If the image remains distorted after improving the signal, the problem is probably the camera’s hardware rather than the network, and replacement will be necessary.
A well-executed installation results in a stable system, with cameras recording continuously, sharp images and working remote access from any mobile device. Investing in initial planning, especially in correct network configuration, saves hours of troubleshooting and avoids recurring support calls.
What is the difference between a router in AP mode and router mode for camera systems?
In router mode, each device creates its own subnet, which fragments communication between cameras and the NVR. In AP mode, the device functions only as a wireless access point, keeping all devices on the same network and allowing a single DHCP server to assign IP addresses centrally. For video surveillance systems, AP mode is almost always the correct choice, as it ensures the NVR can discover and communicate with all cameras without NAT barriers.
What disk capacity is recommended for an NVR with multiple cameras?
The ideal capacity depends on the number of cameras, recording resolution and desired number of retention days. As a general rule, for a system with 4 to 8 cameras recording in Full HD with motion detection, a 1 TB disk supports between 7 and 15 days of recording. For retention of 30 days or more, 4 TB disks or higher are recommended, preferably models certified for video surveillance such as WD Purple or Seagate SkyHawk, optimized for continuous writing 24 hours a day.
What to do when an IP camera’s image appears distorted or with lag?
Image distortion can have two distinct origins: hardware or network. If the distortion is permanent and does not improve with a better Wi-Fi signal, it is very likely that the camera’s optical module or sensor is damaged, requiring replacement of the equipment. If the problem is lag, the cause is usually a weak Wi-Fi signal. The solution is to install a repeater or additional access point closer to the camera, which usually resolves the delay without needing to replace the camera.
Need help? Contact MEGABIT at comercial@megabit.ptin-person support in Baixa do Porto and the entire Northern Portugal region.
Want to be notified when we publish our next article or video?
Free. Get notified as soon as we publish. No spam, easy to unsubscribe.


